GENERIC allows to use 0MQ as a dumb networking framework.
It provides user with connect/disconnect notifications.
Also, each inbound message is labeled by ID of the connection
it originated from. Outbound messages should be labeled by
the ID of the connection to send them to.

To distinguish connect/disconnect notifications from common
messages, COMMAND flag was introduced.
Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

This patch simplifies the whole codebase significantly,
including dropping depedency on libuuid.
Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

It was used only by ROUTER socket. After its removal it became
obsolete.
Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

It is now maintained as a separate project.
Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

To be replaced by new generic socket type
Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

The test now checks whether replies are dropped when reply pipe
is overflowed.
Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

As PGM is not capable of passing subscriptions upstream,
subscriptions are ignored at sub side and engine subscribes
for all messages on pub side.
Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

The filtering is now done depending on the socket type. SUB socket
filters the messages (end-to-end filtering) while XSUB relies
on upstream nodes to do (imprefect) filtering.
Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

Till now the VSM buffer was aligned to 16 bit boundary
which could possibly cause problems on RISC architectures
when accessing the message data in unsafe manner.
Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

autogen.sh incorrectly referred to the license as GPL.
Changed to LGPL.
Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

recv function on eventfd signaler could accidentally
grab two signals instead of one. Fixed.
Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

Eventfd (on Linux) is more efficient that socketpair
for passing simple signals.
Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

Storing commands in OS socket buffers caused whole lot of
problems when free space in the buffer ran out. This patch
stores commands in ypipes instead and uses socketpair just
to signal the other thread, ie. at most one byte is stored
in the socketpair at any single instant.
Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

pthread_* functions return the error number rather than
setting errno. This was not accounter for till now.
Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

IPv6 addresses have colons and will produce invalid data for the getaddrinfo lookup.
Signed-off-by: Andrew Thompson <andy@fud.org.nz>

MSVC project files for inproc_lat and inproc_thr were not
packaged during make dist phase.
Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

Signed-off-by: Carl Clemens <carlclemens1@yahoo.com>

Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

So far the requests in req/rep pattern were delivered to and processed
by worker even though the original requester was dead. Thus,
the worker processing replies with noone to deliver results to.
This optimisation drops requests in two situations:

1. Queued inbound requests in XREP socket when peer disconnects.
2. Queued outbound requests in XREQ when socket is closed.
Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

Up to now the complexity of fair-queueing in XREP was O(n).
Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

This patch introduces two changes:
1. 32-bit ID is used to identify the peer instead of UUID
2. REQ socket seeds the label stack with unique 32-bit request ID
   It also drops any replies with non-matching request ID
Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

So far there was no distinction between message parts used by 0MQ
and message parts used by user. Now, the message parts used by 0MQ
are marked as 'LABEL'.
Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

Signed-off-by: Martin Sustrik <sustrik@250bpm.com>

For the platforms that don't support MSG_DONTWAIT the reader
socket in mailbox_t was kept in non-blocking state and flipped
to blocking state and back when blocking read was requested.
Now, the state is preserved between calls and flipped only
if different type of operation (block vs. non-block) is
requested.
Signed-off-by: Fabien Ninoles <fabien@tzone.org>
Signed-off-by: Martin Sustrik <sustrik@250bpm.com>